BLUECAST X5 RESIN FOR LCD/DLP Ver más grande

BLUECAST X5 RESIN FOR LCD/DLP

Nuevo


Superior castable for LCD and DLP printers
Castable
: YES - Castability: Excellent

Compatible with: all LCD printers like Wanaho D7Anycubic 3d, Micromake L2, X-Cube, Xayav V etc. (405 nm with 30 watt led or higher power) 

Washing mode: Ethyl / IPA alcohol 30 seconds _ Drying with compressed air

UV care: Not needed

Shrinkage: Minimum

Color: Light Blue

Primercat: Suggested

Size: 500 gr

BLUECAST X5 FOR LCD DLP

- Custom syntetized oligomer by BlueCast, not available to market, patent is going to be applied.

- Excellent casting of small engravings both positive and negative

- Fits all jewelry needs from filigree to medals as well dental one

- Excellent for stones presetting

- Curing triggering tuned to maximize antialias smoothing

- No monomer inside, no smell

- No aggression on plastic parts (tested on PS, PMMA)

- No postcuring needed for casting

- No shrinkage

- Easy welding with wax, forget about pattern lost into investment

- Can be polished, engraved, drilled (postcure is needed)

- Low viscosity, easier to recover uncured resin from models, easy to wash

- No preheating required

- Very little hygroscopic while liquid, no water absorption while printed

- Atoxic, solvent free, very low phospine content, very low skin irritant

- Cleaner burnout, 0,00% ash residual

- Suitable for fast burnout

- Full burnout also at lower temperature (750 C°)

- No expansion during burnout, sublimation starts at 130 Celsius

- Excellent dimensional stability in time, no need to stock in cold/dark places

Bajo demanda

140,00 €

Reseñas

No hay comentarios de clientes por ahora.

Escribe tu opinión

BLUECAST X5 RESIN FOR LCD/DLP

BLUECAST X5 RESIN FOR LCD/DLP


Superior castable for LCD and DLP printers
Castable
: YES - Castability: Excellent

Compatible with: all LCD printers like Wanaho D7Anycubic 3d, Micromake L2, X-Cube, Xayav V etc. (405 nm with 30 watt led or higher power) 

Washing mode: Ethyl / IPA alcohol 30 seconds _ Drying with compressed air

UV care: Not needed

Shrinkage: Minimum

Color: Light Blue

Primercat: Suggested

Size: 500 gr

BLUECAST X5 FOR LCD DLP

- Custom syntetized oligomer by BlueCast, not available to market, patent is going to be applied.

- Excellent casting of small engravings both positive and negative

- Fits all jewelry needs from filigree to medals as well dental one

- Excellent for stones presetting

- Curing triggering tuned to maximize antialias smoothing

- No monomer inside, no smell

- No aggression on plastic parts (tested on PS, PMMA)

- No postcuring needed for casting

- No shrinkage

- Easy welding with wax, forget about pattern lost into investment

- Can be polished, engraved, drilled (postcure is needed)

- Low viscosity, easier to recover uncured resin from models, easy to wash

- No preheating required

- Very little hygroscopic while liquid, no water absorption while printed

- Atoxic, solvent free, very low phospine content, very low skin irritant

- Cleaner burnout, 0,00% ash residual

- Suitable for fast burnout

- Full burnout also at lower temperature (750 C°)

- No expansion during burnout, sublimation starts at 130 Celsius

- Excellent dimensional stability in time, no need to stock in cold/dark places

Escribe tu opinión